Skip to content

How to setup a roaming wifi network over ethernet with an Airport Extreme and Airport Express

In the past, all the devices in my home operated over a single wifi network—including four Macs, an AppleTV and several iOS devices. I’ve long suspected I was probably overtaxing the wifi, and listening to the recent “taming wifi” episode of the Technical Difficulties podcast inspired me to do something about it.

So my project this weekend was running cat-6 cabling throughout the house, allowing me to move my Macs and AppleTV off the wifi and onto a gigabit ethernet.

As part of that project, I wanted to modify my upstairs/downstairs roaming wifi network from one in which an Airport Express extended the network created by an Airport Extreme over wifi, to one in which the Express extended the network over ethernet. That proved a bit trickier than I expected, so I wanted to explain it here for the potential benefit of others.

To clarify what I wanted to do: Previously, the Airport Express (upstairs) connected to the Airport Extreme (downstairs) over wifi (a network called “Hacienda”), and then extended the “Hacienda” wifi network to the upstairs area of my house. Configuring an Express to do this is very easy; you just select “Extend a wireless network”.

The problem with such a setup, is that the Express is sharing its wifi bandwidth between two functions—communicating with the upstairs devices over wifi, and then passing that same traffic to the Airport Extreme downstairs, over wifi. Now with cabling everywhere, my plan was to connect the upstairs Express to the ethernet, so that it could extend the wifi network upstairs without having to communicate with the downstairs Extreme over wifi.

Unfortunately, that wasn’t as easy as just connecting the Express to the ethernet. In fact, doing just that caused all sorts of problems; all of a sudden my upstairs Macs started popping up those warnings, “This Mac’s IP address is already in use by other computer with the same name…”

The solution is to configure the upstairs Express in precisely the same way as the downstairs Extreme—i.e. you “create a wireless network” with the same name (“Hacienda” in my case) and the same password, and set the device to operate in “bridge mode”. Doing that, and everything works as expected.

So, wrapping up, here’s a diagram of what my network looked like before and after:

If you’re looking to do the same thing, I hope this article has helped. And if you have any questions, don’t hesitate to write.

Published inTechnology


  1. Nick Schaub Nick Schaub

    I have run the very same setup for a couple years. I have two AIrport express on opposite ends of the house on main floor connected back via CAT5 to Extreme in basement. Signal is 5/5 at any given place in the house. Handoff between access points is not smooth, however. If I recall correctly the wifi protocol sets system gain early in a given transmission so if you are mobile between two access points you might have issues. I don’t believe 802.11 a-n were intended for roaming use in the first place. I think AC may have adapted more for that purpose.

  2. phillip phillip

    Large house we have 3 wireless adapters and this method works, thanks for the confirmation. I was trying to set everything up as an extended wireless network using the wifi. Only addition would be to mention to keep the wireless networks on separate channels.

  3. Neal Neal

    I’ve been looking for an article/how-to on if the Airport Extreme can be in Bridge-Mode as well as the Airport Express being in Bridge-Mode. This is the first I’ve found — all others assume the Airport Extreme is placed to ‘Share an IP Address’ Great article with a simple, yet great diagram. Thank you!

  4. Toine Rodenburg Toine Rodenburg

    Matt, did you buy the cables, rj45s and pliers in an electronic shop locally or online? Can you provide me with a good address ?

  5. nsfbr nsfbr

    Amazingly, I’ve been looking for confirmation that this is the correct answer on the internets for days now. That has included time on the Apple support site and other blogs. None of that has been as clear as this write up. Thanks! I am going to make the leap that in my case, the fact that I’m going to connect the second Airport, in my case a second Airport Extreme, to the ethernet network via a MoCa link (from a TiVo Roamio actually) doesn’t matter. I will post again if I find that to be incorrect.

  6. Nissar Nissar

    Thank you very much for this very simple guide! It looks like it solved my problem. ONE question though, in your diagram above you say that the Airport Extreme (in my case a Netgear Router) has to have Bridge Mode enabled. Is it necessary or is it enough with AirPort Express having Bridge Mode on?

    My setup is:

    ADSL Modem –> NetGear Router R7500 = Created Wireless Network “Home” with password and Bridge Mode DISABLED –> Wired connection from the NetGear Router R7500 to Airport Express = Created Wireless Network “Home” with password and Bridge Mode ENABLED.

    Is it fine?

  7. elynmac elynmac

    This works. We looked everywhere. But this is the only solution that worked. I want to note that we had the same error message coming all the time: “This mac’s ip address is already in use by another computer” Now we are fine. Bless you.

  8. Greg Greg

    Great write up. Can you clarify in your diagram if you are directly connecting your upstairs airport express to the downstairs airport extreme or if the upstairs unit connects directly to your router?

    Apple seems to suggest you daisy chain the devices (modem -> airport -> airport) but I haven’t been able to do this with both in bridge mode. In my case, I need my firewall / router to provide DHCP and both airports to be in bridge mode.

    • Matt Henderson Matt Henderson

      Hi Greg, both airports and the router reside on the same ethernet network (i.e. they are connected to the same ethernet switch). Hope that helps!

  9. Invino Veritas Invino Veritas

    Nope. Nada. Didn’t work….
    We have two networks (“company” and “company 5ghz”).
    Walk out of range of one and 5gh goes away. Also, use the other network and it never jumps to full signal, even though two airports share the exact same back end HP procurve switch. Networks are identical. Both have a static internal IP in bridged mode.

    In all my years of networking, this is by far the most frustrating, time consuming, crap product I’ve ever used. Ruckus is far easier and more reliable.

  10. mf mf

    Thanks so much for this article.

  11. Martin Guan Martin Guan

    Thanks – you saved me from doing bad things to my expensive Apple gear 🙂

  12. durant grenwood durant grenwood

    i have set this up, but the second AE is only getting 2-4 mbps speeds during tests, the first AE is getting closer to 100mbps in tests. during speed test on second AE the light blinks and airport utility says it is not part of network anymore. then it comes back on network. both SE’s setup in bridge mode with same SSID and password. any ideas?

    • durant grenwood durant grenwood

      by the way, my AE’s are daisy chained together. not both plugged directly into router. i thought that my way was the way Apple suggested. but if plugging both into router will cure my ills, i will try it.

  13. Mark Schneyer Mark Schneyer

    Thanks you for your article. I want to do something similar but have my verizon gateway modem/router sever as both my modem and wireless router. It is connected to an ethernet switch in my basement. I wanted to move my airport extreme (currently functioning as my wireless router, the wireless radio is turned off on my verizon gateway router) to my basement and connect it to the ethernet switch and use it to create a roaming network to provide better wife coverage in my basement. is this possible? Thanks

    • Matt Henderson Matt Henderson

      Mark, you mentioned that your Verizon gateway serves as your wireless router, but then mentioned later that the wireless radio is turned off. You can definitely connect your AirPort Extreme to your router, and create a wireless network, but that seems like it’d be your ONLY wireless network.

  14. javier javier

    this is great. HOwever, when I set up the airport extreme router mode to off (bridge mode) I lost internet connection to get it back when I switch back to DHCP and NAT

  15. Jeff Jeff

    Airport Utility 6 doesn’t offer an obvious bridge mode selection. How do I configure the same network using the current Airport Utility?

    • Agora Agora

      Jeff, after you set up the Airport Express as a new network, there will then be an icon of the AE in the Airport Utility. If you click on the AE icon there, and click edit, you’ll see settings for the AE. The bridge mode setting is in the network tab.

      Thanks for the article, Matt. So stupid that Apple doesn’t seem to have this in their documentation.

  16. Arjun C Arjun C

    Your five year old blog post is still very relevant. Even more useful than Apple’s documentation. Thank you!

    Just used this to setup my Airport Express on bridge mode by creating a new wireless network. My other Time Capsule automatically set itself up on bridge, but with the Express, I had to create a network first and then manually change setting to bridge mode.

    • Matt Henderson Matt Henderson

      Wow, thanks for the kind words, and glad it was of use!

  17. Jennifer T Jennifer T

    I am SOOOOOOO grateful you posted this article! I have spent the last 3 weekends engaged in an identical project- running CAT 6 ethernet for my home LAN, working in the insulation-filled attic, cutting surgical precision holes in the walls and one floor, reclaiming a corner of the workshop for the networking closet) and lo and behold I created exactly the same issue with IP addresses already in use, bringing the network to its knees Monday mid-day just prior to a work Teams meeting my husband had (AUGH!!!!!!!). I was just about to break out the IT Shaman tool kit (because it was clearly time to resort to assistance from the spirits infecting my hardware) when I found your article.

    Thank you for posting your problem and solution in such crisp detail. Indeed your documentation is more useful than Apple’s AND it’s still useful in early 2021 (for those of us who love our old AirPort Extreme and recently purchased a second from eBay to create a fast roaming network). And thank you for leaving this up on the internet where the rest of us can locate it!

    • Matt Henderson Matt Henderson

      Hi Jennifer, I’m SO happy you found the article useful! Thanks so much for the feedback. 🙏 🎉

Leave a Reply to Matt Henderson Cancel reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.